conteHome > Smart Array > Hp P420i Linux Driver

Hp P420i Linux Driver

Contents

asked 4 years, 5 months ago viewed 3,376 times active 3 years, 1 month ago Linked 168 LVM dangers and caveats 51 Why are my XFS filesystems suddenly consuming more space Arrayprobe) which may need modifications to work with the hpsa driver. The following message would be reported - “Device appears more than once in tree”. Does it matter if I replace germanium transistors with silicon? http://kssrt.com/smart-array/hp-p420i-driver.php

Read the README file for information about how the tarball is used in the source RPM. Yes you right, hpsa is in the kernel since I did not had to built the module or something like that. Open Windows Explorer Right-click on Computer Select "Properties" Look for the "System" heading to find the "System type" A 64-bit system may shown as: "64-bit Operating System" Subscribe to driver and Navigate to HP Smart Array B320i Raid Configuration 3. Get More Information

Hp Smart Array P420 Controller Firmware

Fixed race condition that could show up during driver init. You should also leverage the Tuned framework with: tuned-adm profile enterprise-storage to set readahead, nobarrier and I/O elevator to a good baseline. Using XFS on fibre channel storage does not show the problem. Notes:Deliverable Name:      Supplemental Update / Online ROM Flash Component for Linux (x64) - Smart Array P220i, P222, P420i, P420, P421, P721m, and P822   Release Version and/or Date:      6.68

I haven't yet tested the firmware workaround with 16.04. The function prints a message then retries the command that returned with a unit attention. Place the desired firmware to be updated in the directory, /hp/swpackages on the USB key. Smart Array P420i Latest Firmware Terrible.

This means that logical drives which would be presented with devices nodes like "/dev/cciss/c0d0", etc. You want a cache ratio biased towards writes versus reads. 75:25 is the norm. For additional information please refer to the customer advisory # c04719000 I/O may halt when the drive write cache is enabled.    Known Issues:      None Upgrade Requirement:Recommended - HPE recommends users I'd potentially try this without LVM.

Change to DISABLED share|improve this answer edited Mar 31 '13 at 13:34 answered Mar 30 '13 at 13:27 ewwhite 162k65332643 I've Oracle Enterprise Linux 5.5 I will download and Smart Array P420i Cache Module Installation:To update firmware from Linux operating system on target server: Updating firmware with rpm installed: Install the firmware rpm using the command:  rpm -ivh .  This extracts the contents of the Important: When booting a system running Red Hat Enterprise Linux 7.1 Operating System, the HP Smart Array controllers might not be recognized. For systems with the B320i SAS controller: 1.

Hp Smart Array P420i Driver

Normally it's in OIL. Are you using XFS partitioning during installation or creating the partitions after the fact? Hp Smart Array P420 Controller Firmware Especially on HP Smart Array controllers, where there are some LVM-like functions native to the device. P420i Controller Does anyone have some experience about it to help me?

If there's something else I can check to help track this down, please tell me. this content Version:6.68 (1 Oct 2015) Fixes Upgrade Requirement:Recommended - HPE recommends users update to this version at their earliest convenience. Does a history of social anxiety significantly damage commercial pilot career prospects? This patch will get called only once for each controller. Smart Array P420i User Guide

These won't work with very old kernels such as the 2.4.7 series used by SLES 7.0, etc. Added support for non-hotplug disk drives. Please see the footnotes on the HP/OEL technical exceptions matrix. weblink The actual name of the 'hp-firmware-smartarray-46a4d957a7-*' folder is based on the version of the rpm installed in the step above The results of the firmware upgrade are saved to the Component.log

By using this site, you accept the Terms of Use and Rules of Participation current community chat Server Fault Meta Server Fault your communities Sign up or log in to Hp Smart Array P420 Controller Battery Replacement UPDATE: The same for Oracle Enterprise Linux 6.2 and 6.4 linux hp hp-proliant hp-smart-array fakeraid share|improve this question edited Mar 31 '13 at 13:33 ewwhite 162k65332643 asked Mar 30 '13 at The hpsa driver has the ability to claim unknown Smart Arrays, however this is turned off by default so that it does not try to claim older controllers meant to be

As a note, the kernel version I used for this test was 2.6.39.

Updated rebuild_lun_table to avoid pulling a logical volume out from under acuxe or hpacucli. but I can not install os at all. We tried and observed many things already, none of the following have helped: Using numactl to influence memory allocations. Dl380p Gen8 Firmware Select driver language and OS Driver language Chinese (Simplified) Chinese (Traditional) English French German Italian Japanese Korean Spanish Operating systems in English Select your product's operating system Citrix XenServer 6.x Citrix

vmstat/iostat We have a MySQL replication setup, using mysql 5.5. If you've been using cciss already on these controllers, it is not recommended that you attempt to upgrade your running system to switch from cciss to hpsa unless you have a Fix procfs regression. check over here where do bad papers go to die?

For additional information please refer to the customer advisory # c04602866 Enhancements Enhancements/New Features: Improved error handling when hard disk drives generate a large number of recoverable errors. If you do a lot of fsync, your raid card can not fake those logs writes anymore. xfs_info output: [[email protected] ~]# xfs_info /mysql/bp/ meta-data=/dev/mapper/sysvm-mysqlVol isize=256 agcount=16, agsize=4915136 blks = sectsz=512 attr=2 data = bsize=4096 blocks=78642176, imaxpct=25 = sunit=64 swidth=192 blks naming =version 2 bsize=4096 ascii-ci=0 log =internal bsize=4096 Fixed issue where controllers that had no configured volumes did not show up in the OS.

The hpsa driver is available in the kernel.org kernels, and in RHEL6 by default, and in SLES11 (but not by default).

nt